Combustible Metal Dust Explosion
AL Solutions Metal Dust Explosion and Fire
AL Solutions, Inc.
📍 New Cumberland, WV
Incident: December 9, 2010 • CSB Report: July 16, 2014
3
Fatalities
1
Contractor Injured
Zirconium and Titanium Metal Dust
Chemical / Hazard
4
CSB Recommendations
📋 Incident Summary

At about 1:20 p.m. on December 9, 2010, a metal dust explosion and fire at the AL Solutions facility in New Cumberland, West Virginia, killed three employees and injured a contractor. The facility milled and processed scrap titanium and zirconium, blended the powder, and pressed it into dense disks called compacts.

A blender used to process zirconium had mechanical problems that had not been adequately repaired and was producing heat or sparks from metal-to-metal contact. A spark or hot spot likely ignited the zirconium powder inside. The flash fire lofted metal dust in the blender into a burning cloud, which ignited other dust in the building and caused a secondary explosion.

The facility had fatal fires and explosions involving metal dust in 1995 and 2006, and at least seven fires requiring a fire department response between 1993 and 2010. AL Solutions did not follow NFPA 484, the standard for combustible metals. The CSB's final report, released July 16, 2014, made 4 recommendations and reiterated its call for an OSHA combustible dust standard.

🔎 Key Findings
Finding 01
Blender Problems Not Repaired
A zirconium blender with mechanical problems was producing heat or sparks from metal-to-metal contact.
Finding 02
Secondary Explosion
The initial flash fire lofted dust into a burning cloud that ignited accumulated dust in the building, causing a secondary explosion.
Finding 03
History of Fatal Dust Events
The facility had fatal metal dust fires and explosions in 1995 and 2006 and at least seven fires requiring fire department response from 1993 to 2010.
Finding 04
NFPA 484 Not Followed
AL Solutions did not voluntarily follow NFPA 484, and no federal OSHA standard required similar controls.
Finding 05
No OSHA Combustible Dust Standard
The CSB reiterated its 2006 recommendation that OSHA issue a general industry combustible dust standard.
🔍 Root Causes
1
Ignition source in equipment
A malfunctioning blender created sparks or hot spots in zirconium powder.
2
Dust accumulation
Combustible metal dust in the building fueled a secondary explosion.
3
Lessons from prior events not applied
Earlier fatal events did not lead to adoption of NFPA 484 practices.
☑ CSB Recommendations
→ AL Solutions (2)
Apply NFPA 484 chapters on titanium, zirconium, fire protection, and combustible metal recycling to all equipment and operations, and train all employees and contractors on combustible dust hazards with annual refreshers.
→ AL Solutions — Burgettstown, PA facility (2)
Prohibit sprinkler and water deluge systems in buildings that process or store combustible metals, and conduct a process hazard analysis per NFPA 484 and submit it to the local fire authority. (All four were closed as unacceptable; the company did not act.)

Full recommendation text and current status: CSB investigation page.

💡 Lessons Learned
Equipment problems in combustible dust service are ignition sources; repair them before running.
Housekeeping prevents a small fire from becoming a secondary explosion.
Repeated fires are warnings; each should drive lasting change.
Combustible metals need specific controls, such as those in NFPA 484, including keeping water away from metal fires.
PHA: Process Hazard AnalysisMI: Mechanical IntegrityTRN: TrainingEAP: Emergency Planning
🔨 Safety Meeting Toolbox Talk
►Do we handle any combustible metal powders?
►Is any of our dust-handling equipment running with known mechanical problems?
►How much dust is on our overhead surfaces?
►What did we change after our last dust fire?
Immediate Action Items
✓Inspect dust-handling equipment for friction and sparking.
✓Audit housekeeping for dust accumulations.
✓Review practices against NFPA 484 for any combustible metals.
🔗 PSM Failures Behind This Incident

This incident involved breakdowns across 4 PSM-related areas (PHA · MI · TRN · EAP). Each represents a gap that process safety programs are designed to close.

Process Hazard Analysis (PHA)
A structured PHA or HAZOP study exists to identify exactly these scenarios before they occur. When PHA is absent, superficial, or overdue for revalidation, hazards operate unseen until they kill someone.
Supporting documents in our library →
Mechanical Integrity (MI)
Equipment must be designed, inspected, and maintained to operate safely in its intended service. Mechanical integrity failures contributed to loss of containment here.
Supporting documents in our library →
Training & Operator Competency
Workers must understand process hazards — not just the steps on the page. Training records, refresher frequency, and verified competency are all OSHA PSM requirements.
Supporting documents in our library →
Emergency Planning & Response
When process safety barriers fail, emergency response capability determines whether the outcome is controlled or catastrophic. Gaps in emergency preparedness amplified the consequences here.
Supporting documents in our library →
Process Safety Management Consulting & Document Library
📂
PSM Document Library
72 ready-to-deploy PSM documents covering all 14 OSHA elements — procedures, checklists, and audit templates built for facilities operating under 29 CFR 1910.119.
Browse the Library →
📊
Free PSM Health Score
Find out where your PSM program stands across all 14 OSHA elements. Our free health score surfaces your biggest gaps in under 10 minutes — no account required.
Check Your Score →
📞
Consulting Services
PHA facilitation, PSM program builds, compliance audits, and OSHA inspection support. Scoped per project with a written proposal before work begins — no retainer required to get started.
View Pricing →
📋 Explore the full incident library: All 111 CSB Case Studies →