Acetylene Backflow — Shed Explosion
Acetylene Service Company Gas Explosion
Acetylene Service Company (ASCO)
📍 Perth Amboy, NJ
Incident: January 25, 2005 • CSB Report: January 26, 2006 (Safety Bulletin)
3
Fatalities
—
Injuries (not stated in CSB summary)
Acetylene Gas
Chemical / Hazard
5
CSB Recommendations
📋 Incident Summary

On January 25, 2005, a gas explosion killed three workers at the Acetylene Service Company plant in Perth Amboy, New Jersey. The blast originated in a wooden shed near six large storage tanks that received liquid waste from the plant's acetylene generating system.

The CSB's Safety Bulletin, Dangers of Flammable Gas Accumulation, found that a check valve did not prevent acetylene from flowing back through the generator water lines. The CSB recommended better isolation of those lines, such as double block and bleed with a vent to a safe location, and an effective PSM program with procedures workers understand.

The bulletin was released January 26, 2006, with 5 recommendations.

🔎 Key Findings
Finding 01
Acetylene Backflow
A check valve did not prevent acetylene gas from flowing back through the generator water lines.
Finding 02
Gas Accumulated in an Enclosed Shed
The explosion originated in a wooden shed near the waste storage tanks.
Finding 03
Weak Isolation
The CSB recommended double block and bleed or equivalent isolation on generator water lines.
Finding 04
PSM Program Needed
The CSB recommended an effective PSM program with written procedures and checklists workers understand.
Finding 05
Outdated OSHA Standard
OSHA's acetylene standard referenced obsolete Compressed Gas Association pamphlets.
🔍 Root Causes
1
Reliance on a check valve
A single check valve was the only barrier to backflow.
2
Flammable gas accumulation
Acetylene accumulated in an enclosed structure with ignition sources.
3
Procedures and training
Procedures were not effective or understood by the workers using them.
☑ CSB Recommendations
→ Acetylene Service Company (2)
Improve isolation on generator water lines with double block and bleed, and implement an effective PSM program with understandable procedures and training.
→ Rexarc, Inc. (2)
Inform generator users that the check valve did not prevent backflow, and replace check valves of that design with more reliable valves.
→ OSHA (1)
Update the acetylene standard to remove obsolete references, for example by incorporating NFPA 51A.

Full recommendation text and current status: CSB investigation page.

💡 Lessons Learned
Check valves are not positive isolation; use double block and bleed for flammable gas.
Prevent flammable gas from accumulating in enclosed structures.
Procedures must be written in a way workers understand and actually follow.
Outdated standards are a warning to look for current good practice.
SOP: Operating ProceduresMI: Mechanical IntegrityTRN: TrainingPSI: Process Safety Information
🔨 Safety Meeting Toolbox Talk
Topic: Flammable Gas Accumulation & Backflow Prevention
►Where do we rely on a check valve to keep flammable gas out?
►Could gas accumulate in any shed or enclosure?
►Are our procedures understood by the people using them?
►Which standards we use reference outdated documents?
Immediate Action Items
✓Identify check-valve-only isolations on flammable gas systems.
✓Ventilate or eliminate enclosures near flammable gas sources.
✓Review procedures with operators for clarity.
🔗 PSM Failures Behind This Incident

This incident involved breakdowns across 4 PSM-related areas (SOP · MI · TRN · PSI). Each represents a gap that process safety programs are designed to close.

Operating Procedures (SOPs)
Operators cannot reliably hold safe operating limits without clear, current, enforced procedures. Deviation from acceptable operating conditions is a direct consequence of SOP failure.
Supporting documents in our library →
Mechanical Integrity (MI)
Equipment must be designed, inspected, and maintained to operate safely in its intended service. Mechanical integrity failures contributed to loss of containment here.
Supporting documents in our library →
Training & Operator Competency
Workers must understand process hazards — not just the steps on the page. Training records, refresher frequency, and verified competency are all OSHA PSM requirements.
Supporting documents in our library →
Process Safety Information (PSI)
Accurate, complete Process Safety Information is the foundation every other PSM element depends on. When PSI is missing or wrong — chemistry data, equipment specs, P&IDs — the entire hazard analysis is built on a flawed base.
Supporting documents in our library →
Process Safety Management Consulting & Document Library
📂
PSM Document Library
72 ready-to-deploy PSM documents covering all 14 OSHA elements — procedures, checklists, and audit templates built for facilities operating under 29 CFR 1910.119.
Browse the Library →
📊
Free PSM Health Score
Find out where your PSM program stands across all 14 OSHA elements. Our free health score surfaces your biggest gaps in under 10 minutes — no account required.
Check Your Score →
📞
Consulting Services
PHA facilitation, PSM program builds, compliance audits, and OSHA inspection support. Scoped per project with a written proposal before work begins — no retainer required to get started.
View Pricing →
📋 Explore the full incident library: All 111 CSB Case Studies →